Flow: Top Receiver TLD
This workspace report displays the top level domains (the last portion of an Internet domain name, such as .com, .edu, or .us) to which traffic is routed over the selected interface in the selected direction (Inbound, Outbound, Inbound and Outbound, or Bounce). The traffic displayed for each TLD is the sum of the traffic received by each device on that TLD.
In most cases, the TLD for a device is the same as the country that is listed in the Top Sender and Receiver Countries workspace reports. However, in the case of the TLD, the country is where the domain name was obtained, and not necessarily where the host is located.
- . Displays an icon and the extension that represents the top level domain.
- . Displays a definition of the extension that is used to represent the top level domain.
- . Displays the bytes per second for the report category.
- . Displays the percentage of the total available bandwidth used by the report category.
: Usage is displayed as N/A if a speed is not specified for the interface. You can set this speed on the Flow Interface dialog. To navigate to the Flow Interface dialog, right-click on the interface on which you want to set the speed, then click .
. Displays the percentage ranking of the item within the top "n" items of the report category.
: You can hover over information in the column to display popup information with average data speed as a percentage of the total interface capacity.
For more information
About interface traffic directions
: For illustration purposes, the descriptions and diagrams in the table below assume that traffic is passing from an internal interface to an external interface or vice versa. In reality, traffic may pass from an internal interface to another internal interface, an external interface to another external interface, or traffic may be routed out the same interface it enters.
Interface
|
Traffic Direction
|
Report displays...
|
Internal interface
|
Inbound
|
The top domain types used by devices on the LAN segment connected to the selected internal interface that are receiving traffic from outside devices.
|
Outbound
|
The top domain types used by outside devices that are receiving traffic from devices on the LAN segment connected to the selected internal interface.
|
Inbound/
Outbound
|
The top domain types used by all devices transferring traffic across the selected internal interface.
|
External interface
|
Inbound
|
The top domain types used by devices connected to the selected external interface that are receiving traffic from devices on an internal LAN segment.
|
Outbound
|
The top domain types used by devices on internal LAN segments that are receiving traffic from devices connected to the selected external interface.
|
Inbound/
Outbound
|
The top domain types used by all devices transmitting traffic across the selected external interface.
|
Linking to Flow Monitor reports from WhatsUp Gold
There are several ways to connect to the Flow Monitor Interface Details report from this WhatsUp Gold workspace report.
- Click the interface name at the top of the workspace report to view the Flow Monitor Interface Details report for the selected interface.
- Click an entry in the far left column of the workspace report to view the Interface Details report for the selected interface. The entry that you click will be applied to the report as a keyword filter.
Configuring this workspace report
- In the title bar of the workspace report pane, select . The Configure Report dialog appears.
- Enter or select the appropriate information in the following fields.
- . Enter a title for the workspace report. This name appears in the title bar of the workspace report's pane.
- . Select the timeframe for the traffic about which you want to see a report. You can select either the last 5, 15, or 30 minutes, or the last hour.
- . Select the router interface that is used by the traffic you want to see in this report.
- . Select a direction for which the report will display data for the selected interface (In, Out, or Both).
- . Enter the number of records you would like displayed in the workspace report.
- . Select the type of data you would like displayed within the workspace report (Chart and data, Data only, Chart only).
- . Select the type of chart you would like the report to display.
- . Specify how wide, in pixels, the graph or chart should appear.
- . Specify how tall, in pixels, the graph or chart should appear.
- . Click this button to apply a filter by which report data will sort. After clicking, filter fields appear below the button.
Select the type of filter you want to apply. If appropriate, select a secondary filter type from the second filter field. For more information on filters, see Filtering Flow Monitor workspace reports in WhatsUp Gold.
: Filters applied here are listed at the top of the workspace report in.
- Click to save changes.